verizon router dhcp getting a fixed IP address

I am currently using Verizon DSL to connect to the internet. So, I have

laptop -> router -> internet

A minor irritation with this set up is that the router can potentially assign different IP addresses whenever I do a reboot or something akin to /etc/init.d/networking restart. For example today it can be 192.168.1.58, tomorrow it could be 192.168.1.68 etc.,

I currently have

$ifconfig                                                                                                                             
eth0      Link encap:Ethernet  HWaddr 00:15:c5:19:9c:1a  
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:17 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:6790 errors:0 dropped:0 overruns:0 frame:0
          TX packets:6790 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:773105 (754.9 KiB)  TX bytes:773105 (754.9 KiB)

wlan0     Link encap:Ethernet  HWaddr 00:13:02:9e:cc:1b  
          inet addr:192.168.1.21  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fe80::213:2ff:fe9e:cc1b/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:7486622 errors:0 dropped:0 overruns:0 frame:0
          TX packets:4833561 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:2650697959 (2.4 GiB)  TX bytes:608573891 (580.3 MiB)

To have the same IP address, say 192.168.1.78, every time the computer is booted

1) Add the following lines to /etc/dhcp/dhclient.conf

alias {
  interface "wlan0";
  fixed-address 192.168.1.78;
  option subnet-mask 255.255.255.255;
}

2) restart the network

sudo /etc/init.d/networking restart

Now you should see

$ifconfig                                                                                                                             
eth0      Link encap:Ethernet  HWaddr 00:15:c5:19:9c:1a  
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:17 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:6790 errors:0 dropped:0 overruns:0 frame:0
          TX packets:6790 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:773105 (754.9 KiB)  TX bytes:773105 (754.9 KiB)

wlan0     Link encap:Ethernet  HWaddr 00:13:02:9e:cc:1b  
          inet addr:192.168.1.21  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fe80::213:2ff:fe9e:cc1b/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:7486678 errors:0 dropped:0 overruns:0 frame:0
          TX packets:4833604 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:2650705479 (2.4 GiB)  TX bytes:608589238 (580.3 MiB)

wlan0:0   Link encap:Ethernet  HWaddr 00:13:02:9e:cc:1b  
          inet addr:192.168.1.78  Bcast:0.0.0.0  Mask:255.255.255.255
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1

Note the new wlan:0 interface which is always assigned to 192.168.1.78.

extract historical versions of a file tracked by git

Say, I have a file test.txt being tracked by git.

$git log test.txt
commit 809ebdbd3c44b9310a7a0f67d61897d5d8f9b6d2
Author: rajulocal 
Date:   Sun Aug 7 14:11:31 2011 -0400

    version 15

commit aec45562ad09257ce85eaf00f5a4fa6912e9e51e
Author: rajulocal 
Date:   Sun Aug 7 14:11:21 2011 -0400

    version 14

commit 7fb63da179a2026ba92a8875ff7d3da881ef5854
Author: rajulocal 
Date:   Sun Aug 7 14:11:11 2011 -0400

    version 13

commit 9b3ca5d3d7497e44c012f5ccd5daced2dd90ec12
Author: rajulocal 
Date:   Sun Aug 7 14:10:51 2011 -0400

    version 12

commit d0b5471fa2abce0057cce1d61240e78c09406c04
Author: rajulocal 
Date:   Sun Aug 7 14:10:40 2011 -0400

    version 11

commit e3af4e1a85b4ff07c31c8dcda47eb41c3f3c830b
Author: rajulocal 
Date:   Sun Aug 7 14:10:26 2011 -0400

    version 10

commit be762c0ee45ec6046fa960cace9acae513b80137
Author: rajulocal 
Date:   Sun Aug 7 14:10:18 2011 -0400

    version 9

commit 03ad798434559300cff26f6a238d7b0f05ad53d2
Author: rajulocal 
Date:   Sun Aug 7 14:09:59 2011 -0400

    version 8

commit 94c50cce3b24e572133eeaedc5bfe00aad568aec
Author: rajulocal 
Date:   Sun Aug 7 14:09:52 2011 -0400

    version 7

commit ab63e2bc7b258f702cc8c516c1f16bafc754cf27
Author: rajulocal 
Date:   Sun Aug 7 14:09:44 2011 -0400

    version 6

commit 16c896d19e00267b63537596485074488cd20a85
Author: rajulocal 
Date:   Sun Aug 7 14:09:37 2011 -0400

    version 5

commit 6937331a12209121ba24d111e1ca5128a3c1e836
Author: rajulocal 
Date:   Sun Aug 7 14:09:21 2011 -0400

    version 4

commit 7ec1c7f98a152f6b760ff1561a3b805cc5e374e9
Author: rajulocal 
Date:   Sun Aug 7 14:09:13 2011 -0400

    version 3

commit 5b3788ad1bdef15c1895a6efefcdd1ea96c840e9
Author: rajulocal 
Date:   Sun Aug 7 14:09:01 2011 -0400

    version 2

commit 1306cba057d6cac06ffd39b9234ce72967dc44f8
Author: rajulocal 
Date:   Sun Aug 7 14:08:35 2011 -0400

    version 1

In order to extract the latest 12 versions of test.txt and store each into a different file, I do

$xtract_hist_git 12 test.txt
$ls m??_test.txt            
m00_test.txt  m02_test.txt  m04_test.txt  m06_test.txt  m08_test.txt  m10_test.txt  m12_test.txt
m01_test.txt  m03_test.txt  m05_test.txt  m07_test.txt  m09_test.txt  m11_test.txt

m00_test.txt is the latest copy of test.txt, m01_test.txt is the latest but one copy, m02_test.txt is the latest but two copy etc.,

xtract_hist_git is this little script

$cat ~/bin/xtract_hist_git           
#! /bin/sh
#
# Author               : Kamaraju S. Kusumanchi
# Email                : kamaraju at gmail dot com
# File                 : ~/bin/xtract_hist_git
# Date (last modified) : Sun Aug  7 14:28:14 EDT 2011

revs=$1
file=$2

for i in `seq -w 0 $revs`
do
  git checkout master~$i $file
  mv $file m${i}_$file
done
git checkout master $file

get all the odd lines in a file

sed can be used to get all the odd or even lines in a file. Consider, for example,

$cat linenums.txt
 line 1
 line 2
 line 3
 line 4
 line 5
 line 6
 line 7
 line 8
 line 9
 line 10

To print all the odd lines

$sed -n '1~2p' linenums.txt 
 line 1
 line 3
 line 5
 line 7
 line 9

$sed -n '2~2p' linenums.txt
 line 2
 line 4
 line 6
 line 8
 line 10

login into a directory after sshing into a machine

To login into a machine via ssh and cd into a particular directory immediately afterwards, use

ssh -t user@machine.name 'cd ~/destination/directory && exec /bin/bash --login -i'

The -t option forces the ssh to open a pseudo-terminal. Without the -t option, ssh does not open the pseudo-terminal when a command is specified.

Commands can also contain variable names. For example,

export DYNAMIC=${PWD#$HOME/}
ssh -t user@machine.name "cd ~/$DYNAMIC && exec bash --login -i"

Other possible uses of the -t option

To see the output of top of a remote machine, use

ssh -t user@remote.machine.name top

Add a number to a variable in shell script

Consider the following shell script

$cat add_variables_02.sh
#! /bin/sh
ov=10;
nv=$((ov+3));      echo $nv
((nv=ov+3));       echo $nv
nv=$ov+3;          echo $nv
nv=`expr $ov+3`;   echo $nv
nv=`expr $ov + 3`; echo $nv

Execute in a shell

$bash add_variables_02.sh 
13
13
10+3
10+3
13

The first two methods nv=$((ov+3)) or ((nv=ov+3)) are faster than the fifth method nv=`expr $ov + 3` as the former uses bash's own feature and the later runs an external command in a subprocess.

Also, note that spaces are needed before and after the '+' character when expr is used.

Tested in Debian Wheezy machine using bash 4.2-1

Further reading

1. info coreutils 'expr invocation'
2. man expr
   

Special thanks to the anon 2011-08-24 5:06 AM for providing the first two methods.

recover an accidentally overwritten partition table

shorter version:

Q. I accidentally overwrote the partition table on my computer. Now it does not boot. Is there any way to restore it back?
A. use the testdisk program. Debian users can install it by doing

# apt-get install testdisk

To run it, use the command

# testdisk

This tool is very powerful, easy to use and interactive. It can be run from a live CD. I used it to recover the ext3, Linux swap partition information.


Long story:

My favorite tool for partitioning is qtparted. I got hooked to it couple of years back when I was trying out a knoppix live CD.

The hard drive of my laptop is /dev/sda. I recently bought a 500 GB external USB hard drive. When I connected the USB hard drive, it was recognized as /dev/sdb. I used the qtparted program to partition the /dev/sdb.



The partitioning process went smoothly. But when I click on the /dev/sdb link in the left tab of qtparted window, there were error messages on my konsole

$sudo qtparted
No Implementation: Support for opening ntfs file systems is not implemented yet.
Error: File system has an incompatible feature enabled.  Compatible features are has_journal, dir_index, filetype, sparse_super and large_file.  Use tune2fs or debugfs to remove features.
Error: File system has an incompatible feature enabled.  Compatible features are has_journal, dir_index, filetype, sparse_super and large_file.  Use tune2fs or debugfs to remove features.

Not sure of what it means, I resorted to cfdisk (a Curses based tool for partitioning).


My intention was to delete all the partitions on /dev/sdb and start afresh. However, I ended up deleting all the ext3, swap partitions on /dev/sda by accident. Notice how cfdisk only lists /dev/sda and nothing about /dev/sdb?

When the changes are committed, it gave an error. It asked me to reboot the machine in order to fix the error.

When the laptop is rebooted, Grub does not load. IIRC, the error code was 17. My computer is now officially in a half baked state with the wrong partition table (all because of my stupidity).

Kumar Appiah suggested me to try testdisk. He used it before to recover some FAT32, NTFS partitions.

So, I popped in an old Ubuntu (hoary) live CD to see if it has testdisk. It does not. The Hoary was released a while back. The official repositories were removed. So a simple

# sudo apt-get update

did not work. I modifed the /etc/apt/sources.list to point to dapper instead of hoary. Then did an apt-get update, apt-get install testdisk.

In order to install testdisk from dapper onto hoary, apt-get wanted to install a new kernal and remove the current kernel. I let the upgrade process run and gave it a 'no' when it wanted to remove the current kernel during the post configure stage. This exited the apt-get process abruptly.

Then, I did a "sudo apt-get -f install" to fix the inconsistent state. I then had to do another "sudo apt-get install testdisk". This time it proceeded without any difficulty.

Once testdisk is installed in the RAM, running it was easy. Just execute

# testdisk

The instructions in testdisk screens are very clear. At the end, I was able to recover my original partition table. Kudos to the authors, Debian maintainers of testdisk and to Kumar for suggesting it.


Useful links:
. websites of testdisk , qtparted
. links to debian packages testdisk, qtparted, e2fsprogs

options in function variables octave

The following octave code shows how to make functions take different paths depending on a user specified choice. It is a little template that comes in handy once in a while.

$cat options_in_function_variables_01.m
# Author : Kamaraju S. Kusumanchi
# Email  : kamaraju at gmail dot com
# Last modified : Tue Jun 15 06:45:15 EDT 2010
function [X] = options_in_function_variables_01(X, choice)

if (strcmp(choice, "square"))
 X = X*X;
elseif (strcmp(choice, "unity"))
 X = X*1;
elseif (strcmp(choice, "cube"))
 X = X*X*X;
else
 printf("choice = %s is not a valid option.\n", choice);
 error("please provide a correct choice");
endif
endfunction

To test it

$octave -qf
octave:1> options_in_function_variables_01(2.2, 'unity')
ans =  2.2000
octave:2> options_in_function_variables_01(2.2, 'square')
ans =  4.8400
octave:3> options_in_function_variables_01(2.2, 'cube')
ans =  10.648
octave:4> 10.648/4.84
ans =  2.2000
octave:5> 4.84/2.2
ans =  2.2000

passing functions as arguments in octave

It is possible to pass functions as arguments to another function in Octave. Consider the following sample code

$ls
cube.m  dynamic.m  script.m  square.m

$cat square.m
function [sq] = square(x)
sq = x**2;
endfunction

$cat cube.m
function [cu] = cube(x)
cu = x**3;
endfunction

$cat dynamic.m
function [ ret ] = dynamic (fh, x)
# fh is a function name passed as a string
# ex:-    b = dynamic("cube", a);
# fh can also be a handle
#         handle = @square;
#         b = dynamic(handle, a);
ret = feval(fh, x);
endfunction

$cat script.m
a=5.0

# bh = b obtained by using handle as arguments
handle=@square;
bh = dynamic( handle, a)

# bs = b obtained by using strings as arguments
bs = dynamic("square", a)

# ch = c obtained by using handle as arguments
handle=@cube;
ch = dynamic( handle, a)

# cs = c obtained by using strings as arguments
cs = dynamic("cube", a)

Run the script.m in octave

$octave3.2 -qf script.m

a =  5
bh =  25
bs =  25
ch =  125
cs =  125

Tested using Debian Lenny (stable), Octave 3.2.4

Further Reading:
1) The section on "Function handles, Inline Functions, and Anonymous Functions" in the octave manual http://www.gnu.org/software/octave/doc/interpreter/Function-Handles-Inline-Functions-and-Anonymous-Functions.html

2) http://rosettacode.org/wiki/Higher-order_functions explains how to do this kind of "calling functions from functions" in various programming languages

load data file with header lines in octave

When a data file contains some header lines before the actual data matrix, octave's dlmread function can be used to read the matrix of data and ignore the headers.

For example,

$cat input_data.m
col1 col2 col3
1, 2, 3
4, 5, 6
7, 8, 9
10, 11, 12

This file contains one header line and a 4x3 data matrix. To read it into octave, create a script called

$cat read_data.m
1;
A = dlmread("input_data.m", SEP=',', R0=1, C0=0);
A

$octave3.2 -qf
octave3.2:1> read_data
A =

1 2 3
4 5 6
7 8 9
10 11 12


For more information on dlmread function, use 'help dlmread' inside octave.

Tested using octave 3.2.4-3 on Debian stable (Lenny).

print a file by line numbers

Consider the file

$ cat name.txt
1 k
2 ka
3 kam
4 kama
5 kamar
6 kamara
7 kamaraj
8 kamaraju
9 kamaraju
10 kamaraju k
11 kamaraju ku
12 kamaraju kus
13 kamaraju kusu
14 kamaraju kusum
15 kamaraju kusuma
16 kamaraju kusuman
17 kamaraju kusumanc
18 kamaraju kusumanch
19 kamaraju kusumanchi

To print the contents of lines between 5 and 8

$ sed -n '5,8p' name.txt
5 kamar
6 kamara
7 kamaraj
8 kamaraju

$echo $?
0

To print the lines 10 to 20, just do

$ sed -n '10,20p' name.txt
10 kamaraju k
11 kamaraju ku
12 kamaraju kus
13 kamaraju kusu
14 kamaraju kusum
15 kamaraju kusuma
16 kamaraju kusuman
17 kamaraju kusumanc
18 kamaraju kusumanch
19 kamaraju kusumanchi

$echo $?
0

Note that this command is successful even though the specified right limit (20) is greater than the number of lines in the file (19).

To print the nth line of a file (w.l.g. say n=8), just do

$ sed -n 8p name.txt
8 kamaraju

$ echo $?
0

End of line is represented by $. So, to print from 17th line till the end of the file, do

$ sed -n '17,$p' name.txt
17 kamaraju kusumanc
18 kamaraju kusumanch
19 kamaraju kusumanchi

$ echo $?
0

tags | print specific lines in a file

No theme index file.dpkg error

While trying to upgrade to texmacs 1:1.0.7.2-1in Sid (unstable) on a machine running Debian Lenny (Stable), I was getting the following error

$sudo apt-get install texmacs
// bunch of apt-get messages

Setting up texmacs-common (1:1.0.7.2-1) ...
gtk-update-icon-cache: No theme index file.dpkg: error processing texmacs-common (--configure):
subprocess post-installation script returned error exit status 1
dpkg: dependency problems prevent configuration of texmacs:
texmacs depends on texmacs-common (= 1:1.0.7.2-1); however:
Package texmacs-common is not configured yet.
dpkg: error processing texmacs (--configure):
dependency problems - leaving unconfigured
Errors were encountered while processing:
texmacs-common
texmacs
E: Sub-process /usr/bin/dpkg returned an error code (1)


Install the gnome-icon-theme package to solve this bug.
$sudo apt-get install -t stable gnome-icon-theme
//bunch of apt-get messages

Selecting previously deselected package gnome-icon-theme.
(Reading database ... 225097 files and directories currently installed.)
Unpacking gnome-icon-theme (from .../gnome-icon-theme_2.22.0-1_all.deb) ...
Setting up texmacs-common (1:1.0.7.2-1) ...
gtk-update-icon-cache: Cache file created successfully.
Setting up texmacs (1:1.0.7.2-1) ...
Setting up gnome-icon-theme (2.22.0-1) ...

running external commands

1. To run external commands while editing a file in vim, use the '!' in the normal mode. For example
   

   :!ls -al
   

   will list the files
   

   :!date
   

   will display the current date.
   
   
2. To read the output of external commands into the current file, do
   

   :r !date
   

   All the commands are run in normal mode. Press ESC key to enter the normal mode in vim.
   
   Further reading:- :help :!
   
   
3. To run external commands in octave, use the system command. Sample octave session looks as
   

   $octave -q
   octave:1> system("date")
   Thu Jun  4 23:49:23 EDT 2009
   ans = 0
   octave:2> [ret_code output] = system("date");
   octave:3> ret_code
   ret_code = 0
   octave:4> output
   output = Thu Jun  4 23:49:40 EDT 2009
   
   octave:5> exit

   Further reading :- "doc system" shows the relevant help pages in octave.
   
   
4. To run external commands in Fortran 90 programs, use the system command. Sample code looks as below
   

   $cat system.f90
   program callsystem
          implicit none
          !to examine the behaviour of the system command
          character (len=100)::cmd
          cmd="echo Wake up Neo"
          !if u are using ifc compiler use -Vaxlib during compilation
          call system(cmd//achar(0))
          call system(cmd)
          call system("date")
          ! The next line also works.
          ! call system("ls")
   end program callsystem
   
   $gfortran system.f90
   
   $./a.out
   Wake up Neo
   Wake up Neo
   Thu Jun  4 23:55:07 EDT 2009

5. To run the external commands in C, use the system command available in stdlib.h. Sample code will be
   

   $cat system.c
   #include stdio.h
   #include stdlib.h
   
   int main() {
        /* Fixme :- <, > in the header files are not showing up on blogspot */
        int ret_code;
        ret_code = system("date");
   
        printf("%d\n", ret_code);
        return 0;
   }
   
   $gcc -Wall system.c
   
   $./a.out
   Fri Jun  5 00:04:14 EDT 2009
   0

   
   Further reading :- man system
   
   All the above are tested in Debian Lenny using vim 7.1, octave 3.0.1, gfortran 4.3.1, gcc 4.3.1
   

file test operators in bash

Often while writing shell scripts, various tests need to be performed on files. For example, we need to check if a file exists before copying it somewhere. We need to check the existence of a directory before writing files into it.

Bash comes with the following list of operators to perform these tests.

Operator    Tests Whether
-e          File exists
-f          File is a regular file
-d          File is a directory
-h          File is a symbolic link
-L          File is a symbolic link
-b          File is a block device
-c          File is a character device
-p          File is a pipe
-S          File is a socket
-t          File is associated with a terminal

-N          File was modified since last read
-O          You own the file
-G          Group id of the file is same as yours

-s          File is not zero size

-r          File has read permission
-w          File has write permission
-x          File has execute permission

-g          sgid flag set
-u          suid flag set
-k          "sticky bit" set

F1 -nt F2   File F1 is newer than F2 *
F1 -ot F2   File F1 is older than F2 *
F1 -ef F2   Files F1 and F2 are hard links to the same file *


!           NOT (inverts the sense of above tests)

* signifies a binary operator (requires two operands).

Reference :- Appendix B of "Advanced Bash-Scripting guide" by Mendel Cooper, Version 6.5. Debian users can get this document by installing the abs-guide package.

sudo apt-get install abs-guide

The necessary files can be found in /usr/share/doc/abs-guide . However, the abs-guide package contains only the html version of the document. A pdf version can be downloaded from http://www.tldp.org/LDP/abs/abs-guide.pdf .

script to get the external IP address

When a machine sits behind a router, it has two IP addresses. One internal (assigned by the router), one external (assigned by the ISP). To find the external IP address of the machine, I use the following script called ip.

$cat ip
#! /bin/sh

# get the external IP address of the machine
# Author : Kamraju Kusumanchi
# Date   : Mon Mar 30 00:08:11 EDT 2009

curl www.whatismyip.org
echo ""

On my machine, I have

$curl --version
curl 7.18.2 (i486-pc-linux-gnu) libcurl/7.18.2 OpenSSL/0.9.8g zlib/1.2.3.3 libidn/0.6.5 libssh2/0.18
Protocols: tftp ftp telnet dict ldap ldaps http file https ftps scp sftp
Features: GSS-Negotiate IDN IPv6 Largefile NTLM SSL libz

Execution

$which ip
/home/rajulocal/bin/ip

$ip
141.153.242.115

IP spoofing with iceweasel

This tutorial explains how to spoof the IP addresses using iceweasel (firefox) web browser on machines running Debian Linux.

1. Install the Iceweasel browser, tor button extension
   

   $sudo apt-get install iceweasel iceweasel-torbutton
   

2. Install the privoxy, tor packages
   

   $sudo apt-get install privoxy tor
   

3. Configure privoxy by adding the following line to /etc/privoxy/config

   forward-socks4a / 127.0.0.1:9050 .
   

   Note the '.' at the end. It is important.
   
   
4. Restart the privoxy
   

   $sudo /etc/init.d/privoxy restart
   Restarting filtering proxy server: privoxy.

5. Restart the tor daemon
   

   $sudo /etc/init.d/tor restart
   Stopping tor daemon: tor.
   Raising maximum number of filedescriptors (ulimit -n) to 32768.
   Starting tor daemon: tor...
   Feb 14 00:14:49.473 [notice] Tor v0.2.0.30 (r15956). This is experimental software. Do not rely on it for strong anonymity. (Running on Linux i686)
   Feb 14 00:14:49.474 [notice] Initialized libevent version 1.3e using method epoll. Good.
   Feb 14 00:14:49.474 [notice] Opening Socks listener on 127.0.0.1:9050
   done.
   

6. Start the iceweasel. Use ctrl+2 to enable tor. The status of the tor button is visible in the right bottom box of the iceweasel window. The screenshots below might be helpful.
   
   
   
   
   
   Note: ctrl+2 acts as a toggle switch to enable/disable tor.
   
   
7. Change the proxy. Right click on the tor button (bottom right corner of iceweasel) -> choose preferences -> select "use custom proxy settings"
   
   
   
   
8. Click on "Test Settings" then click "ok" to test for proxy settings. If everything went successful, there will be a confirmation.
   
   
   
   
9. Check the new spoofed "IP address" by visiting sites such as www.whatismyip.com etc., This will be the IP address seen by the websites you visit.
   
   Tor has its limitations. It will not give complete anonymity but something good enough for most purposes. Use at your own risk.
   

The above tutorial is tested in Debian Lenny, iceweasel 3.0.5, tor 0.2.0.30, privoxy 3.0.9, torbutton 1.2.0.

Back ground story :- While hopping around the internet, I came across some articles which claim to track the "identity thefters" via the IP address hits to a website. This is a good approach but we have to understand that it has its own limitations. Using this article, I just wanted to point out that it is very easy to hide one's IP address tracks. Dont be misled by the IP hits...